 |
Acrylic Lacquer
Conformal Coating 419B
Protects printed circuit boards against moisture,
corrosion, and thermal shock. Protects and insulates electrical
and electronic components and assemblies, including generators,
motors, transformers, relays, and solenoid coils.
Clear tough protective coating, Protects against static
discharge.
service temperature limits: 65C
solids by volume: 18% - solids by weight: 25%
viscosity: 50-55, 20-25 Sec.s NBR.
Remove with M.G. Chemicals cat# 831 Conformal Coating
Stripper
Clean up with M.G. Chemicals cat# 435 Conformal Coating
Thinner
Available Sizes
419B-340G - 340g (12 oz)
Aerosol
419B-1L - 1L
(1 quart) Liquid
419B-4L
- 4L (1 gal) Liquid
419B-20L
- 20L (5.3 gal) Liquid |
 |
Green Overcoat
Pen 4190-GP
Protects printed circuit boards against moisture, corrosion,
and thermal shock. Protects and insulates electrical and
electronic components and assemblies, including generators,
motors, transformers, relays, and solonoid coils. Convenient
pen applicator for precision work.
Green tough protective coating - Protects against static
discharge
service temperature limits: 65C
solids by volume: 18% - solids by weight: 25%
viscosity: 50-55, 20-25 Sec.s NBR.
UV indicator added for O.C. inspection
Remove with M.G. Chemicals cat# 831 Conformal Coating
Stripper
Clean up with M.G. Chemicals cat# 435 Conformal Coating
Thinner
Available Sizes
4190-GP - 0.16 oz Pen |
 |
Silicone
Conformal Coating 422 / 422A
A silicone resin protective coating for applications where
temperature or flexability is a concern. Protects printed
circuit boards against static discharge, arching, moisture,
humidity, corrosion, and thermal shock. Contains a UV
indicator for quality control inspection. Easy to repair.
Directions of Use
Spray an even coat with a minimum application of .048
grams per square centimeter. Application measurements
can be achieved by first weighing the can, then spraying
an even coat, then reweighing the can. Knowing the dimensions
of your board, one can calculate as to whether your application
is within certified limits.
Best results will be obtained by applying to thoroughly
cleaned and dried parts or materials. It is essential
that surfaces be free of any trace of grease or organic
substances.
At room temperature, the product will tack free in approximately
30 minutes, and full cure will be achieved in approximately
48 hours.
Curing may be accelerated by applying moderate heat with
either a convection oven or infrared lamps. We recommend
curing in a convection oven at 65°C (149°F) for
one hour, but other temperature and time conbinations
can work well. Heat curing will improve the physical strength
of this coating.
Available
Sizes
Silicone Conformal
Coating W/UV IND.
422A-340G
- 340 gram (12 oz) Aerosol
Silicone
Conformal Coating Pen
422A-P
- 5ml (0.16 oz.) Pen
Silicone
Conformal Coating
422-1L
- 950ml (1 quart)) Liquid
422-4L
- 4L (1 gal) Liquid
422-20L
- 20L (5.3 gal) Liquid |
 |
Silicone
Conformal Coating Pen 422A-P
Protects printed circuit boards against moisture, corrosion
and thermal shock
Clear tough protective coating - Protects against static
discharge
Dries in minutes - cure time 12 - 48 hours at room temperature
or 1 hour at 65 C (149 F)
Remains flexible from -65 C to 200 C (-85 F to 392 F)
Available Sizes
Silicone Conformal Coating Pen
422A-P - 5ml (0.16 oz.) Pen
|
 |
Conformal
Coating Thinner / Cleaner 435
For thinning M.G. Chemicals Coating up to 50%. Also
for use cleaning workplace and equipment after using
conformal coatings.
Fast evaporating - Highly flammable
Available Sizes
435-100ML - 100 ml (3.4
oz) Liquid with brush cap
435-1L - 1L (33 oz) Liquid
|
 |
Epoxy &
Adhesive Cleaner 8328
Contains Ethyl Lactate. Very effective cleaning solvent
(KB value > 1000). Excellent for wipe claning, ultrasonics
and cold cleaning applications. Very human and environment
safe solvent.
Slow evapouration - Low odour - Safe on most plastics
- Leaves no residue - High flash point (139°F) - Biodegradable
- Leaves no residue
Available
Sizes
8328-500ML
- 500 ml (17 oz) Trigger Pump |
 |
Conformal
Coating Stripper 8310
Removes protective coatings, including epoxy, urethane,
silicones, and acrylics. Also removes carbon, tar, adhesives,
rubber, and some plastics.
Extra Strength - Non-flammable - Non-drip (gel type) -
Safe on metals.
Avoid contact with skin
Available
Sizes
8310-100ML
- 100 ml (3.4 oz) Liquid, with brush cap |
 |
Peelable
Solder Mask 862
Excellent for masking contacts, gold fingers, card edges
and desired areas during conformal coating applications.
Meets MIL-STD-2000 paragraph 5.3.18 parts a, b, and d.
Contains no ammonia
Non corrosive to copper, gold, silver or presoldered surfaces
Opaque pink color turns red when cured
Can be used in water or solvent systems
Anti-static, thixotropic
Tested at temperatures 200°C and 400°C.
Directions of Use
The substrate should be free from grease, oil, and particulate
matter. Applay a 30 to 40 MIL coating to desired area
for best results. May be thinned using deionized water.
Under normal conditions, cure will occur in 1 hour at
25°C (77°F). Cure can be accelerated to 30 minutes
at 65C (150°F). Mask will change from an opaque pink
to a translucent red when completely cured.
Available Sizes
862-150ML - 150ml (5.3
oz) Tube
862-4L - 4L (1 gal) Liquid
|
|